KYOCERA FS-8000C Instrukcja Użytkownika

FS-8000CFS-8000CDFS-8000CN Color PrinterQuick Reference GuideKyocera Corporation14-9, Tamagawadai 2-Chome, Setagaya WardTokyo 158-8610, Japan©2001 by

8 Missing tonerTK-82 #######Install the toner container using a toner kit for the particular color. The printer does not operate when this message is

9Print overrun†Press GOThe print job transferred to the printer was too complex to print on a page. Press the GO key to resume printing. (The page may

10 Toner low TK-82 #######Replace the toner container using a new toner kit.#######: Color of the toner container that needs to be replaced. For examp

11Loading Paper1Pull out the paper feed cassette until it stops. Lift the paper feed roller located on the right side of the cassette upright.Paper St

12 Align the paper stoppers correctly with the markings in the cassette that match the paper size:A4A3B5B4A5FS8000QR.book Page 12 Tuesday, December

13Lower the paper feed roller to its original position. Close the paper feed cassette. Paper Size Indicators PositionPaper GuideSquare the edgesof the

14 Clearing Paper JamsThe figure below is a simplified diagram showing the paper path. You can clear paper jams easily and quickly if you become famil

15[Paper Jam — Feeder # Cover][Paper Jam — Cassette #]Open the paper feeder side cover according to the number in place of #, top (1) to bottom (3). P

16 [Paper Jam — MP Tray][Paper Jam — Duplexer Drawer]Remove the jammed paper onthe multi-purposetray up and towards the right.Lower CoverRollerOpen th

17[Paper Jam — Paper Feed Unit]11Open the front cover. Pull the paper feed unit out completely. Paper Feed UnitRemove the paper by swinging the green-

NoticeNO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION OF THE PRODUCT. SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER’

18 3Remove the paper on the rub-ber belts.Open the fuser access cover by pressing the green-colored lock lever.4FS8000QR.book Page 18 Tuesday, Decem

19 Open the fuser top cover by simultaneously pulling the two lock levers.56Raise the sub-cover by grasp-ing the clip marked as A on the rear side whi

20 87Stopper LeverIf driving the paper in the reverse direction will ease remov-ing the paper, you can turn the wheel in the reverse direction by rele

21CautionUse care not to touch the drum component in the primary transfer unit.Turn the wheel (with gear teeth) on the right-hand side of the pri-mary

22 [Paper Jam — Side Cover]2Open the face-up tray. Open the side cover by pull-ing the handle.Remove the jammed paper. If the paper does not go easily

23[Paper Jam — Option Stacker]Paper jam has occurred in the mailbox/sorter stacker, bulk stacker, or the document finisher which is an optional equipm

24 Toner Container ReplacementThe life of the toner containers depends on the amount of toner required to accomplish your printing jobs. When 5% cover

25Replacing the Toner ContainerNoteYou do not have to turn printer power off before starting the replacement. Any data that may be under printing proc

26 While pressing down the blue-colored lever at the end of the toner container, pull the toner con-tainer out.Take the new toner container out of the

27When the toner container has been replaced, proceed to the next section.Replacing the Waste Toner Bottle Replace the waste toner bottle each time yo

FS-8000C Quick Reference GuideFS8000QR.book Page 1 Tuesday, December 25, 2001 10:47 AM

28 CautionDo not put the lid on the opening of a new waste toner bottle. This could cause damage to the printer.3The old waste toner bottle has a cap

29Replacing the Oil UnitThe oil unit lasts an average of 25,000 pages and must be replaced when the printer displays the Replace Oil kit message.NoteT

30 2Open the front and rear release levers outward and remove the old oil unit.Oil Unit31CoverRemove the seal-ing tapes at both ends of the new oil un

3145Attach the new oil unit. Seat it securely by pressing on the front and rear sides (the PUSH HERE areas). Push the paper feed unit back in. Close t

32 Replacing the Maintenance Kit D (Separation Charger Unit)NoteThe following procedure is not necessary for European countries and Australia.The sepa

33Remove the old separation charger unit from the sec-ondary transfer unit. When you pull the project-ing pin on the front end of the separation char

34 Hold the new separation charger unit so that the project-ing pin is in front of you and pass the green knob (separa-tion charger wire cleaning knob

35Press the MENU key. Press the [U] or [V] key repeat-edly until Others > appears.Press the [Z] key. Press the [U] or [V] key repeatedly until &

36 Cleaning the PrinterThe following parts must be cleaned each time the toner container is replaced:• Registration roller•Belts• Separation charger•

37NoteBe careful not to touch the black sponge roller (the secondary transfer roller) during cleaning as this may adversely affect print quality.1Regi

2 ContentsGuide to the information about the printer ...3Understanding the Error Messages ...

38 Cleaning the Main Charger UnitThe main charger unit needs to be cleaned periodically as it gets contaminated with dioxide after a long usage, causi

39 1Cleaning the main charger wire — Grasp the tab of the clean-ing knob (green) and gently pull out and push it back in 3 to 5 times.Grid Cleaner2Cle

40 When finished, remove the grid cleaner from the printer and discard it. The grid cleaner cannot be reused.Close the front cover.3Lock LeverMain Cha

FS8000QR.book Page 41 Tuesday, December 25, 2001 10:47 AM

FS-8000CFS-8000CDFS-8000CN Color PrinterQuick Reference GuideKyocera Corporation14-9, Tamagawadai 2-Chome, Setagaya WardTokyo 158-8610, Japan©2001 by

3Guide to the information about the printerThe following documentation and CD-ROM are sup-plied:Quick Reference Guide (This bro-chure)This manual prov

4 Understanding the Error MessagesThese messages appear on the printer’s message dis-play when the printer needs the operator’s attention. For more de

5Check wastetoner bottleThe waster toner bottle is not installed or full. Install the waste toner bottle.Clean printerPress GOThe printer has reached

6 ID error The user ID entered on the operator panel for a private job, or a stored job is not cor-rect. Check the user ID that you specified on the p

7KPDL Error ##Press GOKPDL (PostScript) error has occurred. Press the GO key to resume printing. Or, you can abandon printing by the CANCEL key. Loa